On MHO-170 In default configuration, what are GAIA names of Security Group Management ports?
A.
eth1-Mgmt1 and eth1-Mgmt2
B.
eth1-Mgmt1 and eth2-Mgmt1
C.
eth1-Mgmt1 and eth1-Mgmt3
D.
eth1-Mgmt3 and eth1-Mgmt4
Answer:
c
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 2
There is a Security group of 10 Appliances and all of them are up and running. How many Appliances within a Security Group keep the same connection in its connection table in case of NAT?
A.
Between 2 and 4
B.
3
C.
All 10
D.
2
Answer:
a
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 3
One single Appliance supports 1M concurrent connections. How many concurrent connections will support Security Group of 2 Appliances?
A.
2M
B.
500K
C.
4M
D.
1M
Answer:
a
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 4
Orchestrator should be defined in SmartConsole as:
A.
Orchestrator is not defined in SmartConsole
B.
Check Point host
C.
Security Gateway
D.
Host
Answer:
a
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 5
Which is a valid requirement for a supported Maestro appliance?
A.
10GBps and 40Gbps or 100Gbps card with double-VLAN and LLDP support
B.
At least one 10GBps line card
C.
Nothing special as Maestro supports any Check Point appliance
D.
Line card with double-VLAN and LLDP support
Answer:
a
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 6
What is the Orchestrator?
A.
Load balancer
B.
Network Switch
C.
Manager of compute and network resources, load balancer and network switch
D.
None of above
Answer:
d
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 7
In order to set Site (chassis) priority per VS, following command should be used:
A.
From given VS context: set chassis high-availability vs chassis_priority
B.
From given VS0 context: set chassis high-availability vs chassis_priority
C.
From any VS context: set chassis high-availability vs chassis_priority
D.
From VS0 context: set chassis high-availability vs chassis_priority
Answer:
b
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 8
What is an uplink interface used for?
A.
To connect in between Orchestrators
B.
To connect appliances to customer's infrastructure
C.
To connect Orchestrators to customer's infrastructure
D.
To connect in between appliances
Answer:
b
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 9
What is the default Distribution mode?
A.
User
B.
Auto-topology
C.
Manual-General
D.
Network
Answer:
c
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 10
When running asg perf -v in a Dual-Site environment, we can see only Appliances from one of the sites. That means were working in:
A.
VSLS mode
B.
Active /Active
C.
Active / Standby HA mode
D.
This is not Dual-Site, in Dual-Site we always see Appliances from both sites